Mr-Glass Custom & Geometric Windows Nationwide | Sightline Windows & Doors Weston

Mr-Glass Custom & Geometric Windows in Weston: What to Know First

We install and service Mr-Glass custom and geometric windows in Weston as an independent Mr-Glass service provider, with most measured surveys completed within 48 hours of your call and written quotes delivered before any work begins. Typical custom and geometric projects, including arched, curved, and oversized openings, run from initial survey to final installation in two to four weeks depending on glass fabrication lead times. Our pricing starts at $1,850 for standard geometric replacements and scales with opening size, impact rating, and glazing complexity, every dollar named in writing under Haven Clause 1.

Call (754) 812-9260

This page is for Weston homeowners who already own Mr-Glass products and need custom-shaped window solutions, or who are comparing Mr-Glass against other lines for a new architectural opening. If you have a competitor’s written estimate, we review it free. Call (754) 812-9260 to schedule your measured survey.

How Mr-Glass Products Fail - and How We Fix Them

• MG-Impact 5500 series fixed geometric units: The thermal break in the frame extrusion separates at the radius points of arched tops, especially in west-facing Weston openings that cycle through 40-degree daily temperature swings in spring. We see this as a visible gap between frame members or condensation pooling at the arch apex. Our fix is a full frame replacement with the updated MG-Impact 5500-R extrusion, which uses a co-extruded polyamide strip rather than the original snap-in design. We measure the existing rough opening from three reference points before ordering, because radius tops shift subtly over years of thermal cycling.
• MG-Elite custom curved windows: The laminated inner lite delaminates at the curve apex, starting as a hazy arc visible at oblique angles. This is a glass fabrication issue, not installation, caused by inadequate autoclave dwell time on tight-radius bends. We source replacement curved lites from the same Miami-area IG fabricator Mr-Glass uses, but we specify a 15-minute extended dwell, documented on the order. The difference shows up five years later when your neighbor’s curve starts fogging and yours does not.
• MG-Standard oversized picture units: Sash sag in openings over 72 inches wide, where the aluminum stile deflects enough to break the bulb seal against the frame. Weston homes along the Town Center corridor see this accelerated by salt-laden air that corrodes the stainless steel balance shoe. We replace with a reinforced stile using a 6063-T6 alloy rather than the original T5, and we specify 316-grade stainless hardware. The price difference is $140 per unit. We tell you that in writing before we start.
• MG-Impact geometric casements: The multi-point lock system drifts out of alignment because the custom jamb depth does not leave enough meat for the keeper screws to bite securely. This shows up as a handle that turns hard or a top corner that whistles in a northeast wind. We machine a custom backing plate from 1/8-inch 5052 aluminum, through-bolted, rather than relying on the OEM self-tapping screws that back out. It’s a $65 parts addition we disclose upfront, not a surprise.
• MG-Elite trapezoid and pentagon shapes: The insulated glass unit fails at the shortest leg because the fabricator’s standard spacer corner key does not accommodate angles below 22 degrees. We see this in Weston modern builds along Bonaventure Boulevard where architects specify aggressive rake angles. Our fix is a bent-corner warm-edge spacer, hand-formed to the exact angle, with desiccant fill verified by weight before seal. We document the spacer weight on your job record. Measure it right the first time. The window does not care how confident you were.

Our Mr-Glass Custom & Geometric Windows Process

1. 1
   Measured survey. Sonia Raman or a verified crew member arrives in uniform with license number visible, measures every leg and radius from three reference points, and records frame squareness to 1/16 inch. You keep the survey document.
2. 2
   Diagnostic and scope. We identify the Mr-Glass series, document failure mode with dated photos, and specify OEM versus quality aftermarket parts with the trade-off named in writing. For discontinued MG-Standard curved units, we identify the compatible MG-Elite replacement profile or cross-reference to PGT or CGI equivalents if the opening performance requirements allow.
3. 3
   Written quote. The measured survey becomes the quote. Same document, same numbers. No change orders permitted. Haven Clause 1.
4. 4
   Fabrication and staging. We order glass and frame components with specifications noted above, track lead times weekly, and confirm delivery before scheduling installation. For impact-rated custom shapes, we verify the Miami-Dade NOA or Florida Product Approval number matches your wind zone.
5. 5
   Installation and testing. Crew arrives on schedule, installs to the measured survey, tests every operable unit for seal compression and lock alignment, and records a dated photo set of the completed opening. You receive the photo record by email within 24 hours.
6. 6
   365-Day Done Right Promise. If the seal fails, the lock drifts, or the frame shows deflection, we return and make it right. Written into the Haven Standard, not a verbal assurance.

Before

After

What Mr-Glass Custom & Geometric Windows Costs in Weston

Impact-rated custom shapes carry a 20-35% premium over non-impact equivalents due to laminated glass and reinforced framing. Weston sits in the High-Velocity Hurricane Zone, so most exterior geometric openings require impact rating for code compliance on replacement. We verify your specific wind-borne debris zone during survey and note it on the quote. Call (754) 812-9260 for your exact written price. Estimates are free.

Why Weston Homeowners Call Sightline Windows & Doors Weston for Mr-Glass Work

We have measured, ordered, and set Mr-Glass products across Broward County since 2012, with a concentrated run of jobs in Weston where the salt-laden air off the Town Center corridor and the tight architectural review requirements create a specific installation environment. Our crews know the difference between MG-Standard and MG-Elite frame depths by sight, and we carry the full backup of eight manufacturer lines, PGT, CGI, CWS, ES Windows, ECO Window Systems, Therma-Tru, and ViewLux included, if your opening requirements outrun Mr-Glass’s current catalog.

Every technician is background-checked, uniformed, and identified by license number before arrival. Every job leaves a documented photo record. The 365-Day Done Right Promise is stamped on every invoice, not offered as a courtesy. We do not ask you to trust us. We ask you to read the document.

FAQs